[packages/net-snmp.git] / net-snmpd.conf

###############################################################################
#
# EXAMPLE.conf:
#   An example configuration file for configuring the net-snmp snmpd agent.
#
###############################################################################
#
# This file is intended to only be an example.  If, however, you want
# to use it, it should be placed in /etc/snmp/snmpd.conf.
# When the snmpd agent starts up, this is where it will look for it.
#
# All lines beginning with a '#' are comments and are intended for you
# to read.  All other lines are configuration commands for the agent.

#
# PLEASE: read the snmpd.conf(5) manual page as well!

#agentaddress	161,tcp:161

###############################################################################
# System contact information
#

# It is also possible to set the sysContact and sysLocation system
# variables through the snmpd.conf file:

syslocation Unknown
syscontact Root <root@localhost>

# Example output of snmpwalk:
#   % snmpwalk -v 1 localhost public system
#   system.sysDescr.0 = "PLD Linux"
#   system.sysObjectID.0 = OID: enterprises.ucdavis.ucdSnmpAgent.sunos4
#   system.sysUpTime.0 = Timeticks: (595637548) 68 days, 22:32:55
#   system.sysContact.0 = "Root <root@localhost>"
#   system.sysName.0 = "name"
#   system.sysLocation.0 = "Right here, right now."
#   system.sysServices.0 = 72

###############################################################################
# Access Control
###############################################################################

# By far, the most common question I get about the agent is "why won't
# it work?", when really it should be "how do I configure the agent to
# allow me to access it?"
#
# By default, the agent responds to the "public" community for read
# only access, if run out of the box without any configuration file in 
# place.  The following examples show you other ways of configuring
# the agent so that you can change the community names, and give
# yourself write access as well.

# The following lines change the access permissions of the agent so
# that the COMMUNITY string provides read-only access to your entire
# NETWORK (EG: 10.10.10.0/24), and read/write access to only the
# localhost (127.0.0.1, not its real ipaddress).

# For more information, read the FAQ as well as the snmpd.conf(5)
# manual page.

####
# First, map the community name (COMMUNITY) into a security name
# (local and mynetwork, depending on where the request is coming
# from):

#       sec.name	source		community
com2sec	local		localhost	public
com2sec	theworld	default		public

####
# Second, map the security names into group names:

#			sec.model	sec.name
group	MyRWGroup	v2c		local
group	MyROGroup	v2c		theworld

####
# Third, create a view for us to let the groups have rights to:

#           incl/excl subtree                          mask
view all    included  .1                               80

####
# Finally, grant the 2 groups access to the 1 view with different
# write permissions:

#                context sec.model	sec.level	prefix	read   write  notif
access MyROGroup ""      any		noauth		exact	all    none   none
access MyRWGroup ""      any		noauth		exact	all    all    none

# -----------------------------------------------------------------------------


# -----------------------------------------------------------------------------


###############################################################################
# Process checks.
#
#  The following are examples of how to use the agent to check for
#  processes running on the host.  The syntax looks something like:
#
#  proc NAME [MAX=0] [MIN=0]
#
#  NAME:  the name of the process to check for.  It must match
#         exactly (ie, http will not find httpd processes).
#  MAX:   the maximum number allowed to be running.  Defaults to 0.
#  MIN:   the minimum number to be running.  Defaults to 0.

#
#  Examples:
#

#  Make sure mountd is running
# proc mountd

#  Make sure there are no more than 4 ntalkds running, but 0 is ok too.
# proc ntalkd 4

#  Make sure at least one sendmail, but less than or equal to 10 are running.
# proc sendmail 10 1

#  A snmpwalk of the process mib tree would look something like this:
# 
# % snmpwalk -v 1 localhost public .1.3.6.1.4.1.2021.2
# enterprises.ucdavis.procTable.prEntry.prIndex.1 = 1
# enterprises.ucdavis.procTable.prEntry.prIndex.2 = 2
# enterprises.ucdavis.procTable.prEntry.prIndex.3 = 3
# enterprises.ucdavis.procTable.prEntry.prNames.1 = "mountd"
# enterprises.ucdavis.procTable.prEntry.prNames.2 = "ntalkd"
# enterprises.ucdavis.procTable.prEntry.prNames.3 = "sendmail"
# enterprises.ucdavis.procTable.prEntry.prMin.1 = 0
# enterprises.ucdavis.procTable.prEntry.prMin.2 = 0
# enterprises.ucdavis.procTable.prEntry.prMin.3 = 1
# enterprises.ucdavis.procTable.prEntry.prMax.1 = 0
# enterprises.ucdavis.procTable.prEntry.prMax.2 = 4
# enterprises.ucdavis.procTable.prEntry.prMax.3 = 10
# enterprises.ucdavis.procTable.prEntry.prCount.1 = 0
# enterprises.ucdavis.procTable.prEntry.prCount.2 = 0
# enterprises.ucdavis.procTable.prEntry.prCount.3 = 1
# enterprises.ucdavis.procTable.prEntry.prErrorFlag.1 = 1
# enterprises.ucdavis.procTable.prEntry.prErrorFlag.2 = 0
# enterprises.ucdavis.procTable.prEntry.prErrorFlag.3 = 0
# enterprises.ucdavis.procTable.prEntry.prErrMessage.1 = "No mountd process running."
# enterprises.ucdavis.procTable.prEntry.prErrMessage.2 = ""
# enterprises.ucdavis.procTable.prEntry.prErrMessage.3 = ""
# enterprises.ucdavis.procTable.prEntry.prErrFix.1 = 0
# enterprises.ucdavis.procTable.prEntry.prErrFix.2 = 0
# enterprises.ucdavis.procTable.prEntry.prErrFix.3 = 0
#
#  Note that the errorFlag for mountd is set to 1 because one is not
#  running (in this case an rpc.mountd is, but thats not good enough),
#  and the ErrMessage tells you what's wrong.  The configuration
#  imposed in the snmpd.conf file is also shown.  
# 
#  Special Case:  When the min and max numbers are both 0, it assumes
#  you want a max of infinity and a min of 1.
#


# -----------------------------------------------------------------------------


###############################################################################
# Executables/scripts
#

#
#  You can also have programs run by the agent that return a single
#  line of output and an exit code.  Here are two examples.
#
#  exec NAME PROGRAM [ARGS ...]
#
#  NAME:     A generic name.
#  PROGRAM:  The program to run.  Include the path!
#  ARGS:     optional arguments to be passed to the program

# a simple hello world
#exec echotest /bin/echo hello world

# Run a shell script containing:
#
# #!/bin/sh
# echo hello world
# echo hi there
# exit 35
#
# Note:  this has been specifically commented out to prevent
# accidental security holes due to someone else on your system writing
# a /tmp/shtest before you do.  Uncomment to use it.
#
#exec shelltest /bin/sh /tmp/shtest

# Then, 
# % snmpwalk -v 1 localhost public .1.3.6.1.4.1.2021.8
# enterprises.ucdavis.extTable.extEntry.extIndex.1 = 1
# enterprises.ucdavis.extTable.extEntry.extIndex.2 = 2
# enterprises.ucdavis.extTable.extEntry.extNames.1 = "echotest"
# enterprises.ucdavis.extTable.extEntry.extNames.2 = "shelltest"
# enterprises.ucdavis.extTable.extEntry.extCommand.1 = "/bin/echo hello world"
# enterprises.ucdavis.extTable.extEntry.extCommand.2 = "/bin/sh /tmp/shtest"
# enterprises.ucdavis.extTable.extEntry.extResult.1 = 0
# enterprises.ucdavis.extTable.extEntry.extResult.2 = 35
# enterprises.ucdavis.extTable.extEntry.extOutput.1 = "hello world."
# enterprises.ucdavis.extTable.extEntry.extOutput.2 = "hello world."
# enterprises.ucdavis.extTable.extEntry.extErrFix.1 = 0
# enterprises.ucdavis.extTable.extEntry.extErrFix.2 = 0

# Note that the second line of the /tmp/shtest shell script is cut
# off.  Also note that the exit status of 35 was returned.

# -----------------------------------------------------------------------------


###############################################################################
# disk checks
#

# The agent can check the amount of available disk space, and make
# sure it is above a set limit.  

# disk PATH [MIN=100000]
#
# PATH:  mount path to the disk in question.
# MIN:   Disks with space below this value will have the Mib's errorFlag set.
#        Default value = 100000.

# Check the / partition and make sure it contains at least 10 megs.

disk / 10000

# % snmpwalk -v 1 localhost public .1.3.6.1.4.1.2021.9
# enterprises.ucdavis.diskTable.dskEntry.diskIndex.1 = 0
# enterprises.ucdavis.diskTable.dskEntry.diskPath.1 = "/" Hex: 2F 
# enterprises.ucdavis.diskTable.dskEntry.diskDevice.1 = "/dev/dsk/c201d6s0"
# enterprises.ucdavis.diskTable.dskEntry.diskMinimum.1 = 10000
# enterprises.ucdavis.diskTable.dskEntry.diskTotal.1 = 837130
# enterprises.ucdavis.diskTable.dskEntry.diskAvail.1 = 316325
# enterprises.ucdavis.diskTable.dskEntry.diskUsed.1 = 437092
# enterprises.ucdavis.diskTable.dskEntry.diskPercent.1 = 58
# enterprises.ucdavis.diskTable.dskEntry.diskErrorFlag.1 = 0
# enterprises.ucdavis.diskTable.dskEntry.diskErrorMsg.1 = ""

# -----------------------------------------------------------------------------


###############################################################################
# load average checks
#

# load [1MAX=12.0] [5MAX=12.0] [15MAX=12.0]
#
# 1MAX:   If the 1 minute load average is above this limit at query
#         time, the errorFlag will be set.
# 5MAX:   Similar, but for 5 min average.
# 15MAX:  Similar, but for 15 min average.

# Check for loads:
load 12 14 14

# % snmpwalk -v 1 localhost public .1.3.6.1.4.1.2021.10
# enterprises.ucdavis.loadTable.laEntry.loadaveIndex.1 = 1
# enterprises.ucdavis.loadTable.laEntry.loadaveIndex.2 = 2
# enterprises.ucdavis.loadTable.laEntry.loadaveIndex.3 = 3
# enterprises.ucdavis.loadTable.laEntry.loadaveNames.1 = "Load-1"
# enterprises.ucdavis.loadTable.laEntry.loadaveNames.2 = "Load-5"
# enterprises.ucdavis.loadTable.laEntry.loadaveNames.3 = "Load-15"
# enterprises.ucdavis.loadTable.laEntry.loadaveLoad.1 = "0.49" Hex: 30 2E 34 39 
# enterprises.ucdavis.loadTable.laEntry.loadaveLoad.2 = "0.31" Hex: 30 2E 33 31 
# enterprises.ucdavis.loadTable.laEntry.loadaveLoad.3 = "0.26" Hex: 30 2E 32 36 
# enterprises.ucdavis.loadTable.laEntry.loadaveConfig.1 = "12.00"
# enterprises.ucdavis.loadTable.laEntry.loadaveConfig.2 = "14.00"
# enterprises.ucdavis.loadTable.laEntry.loadaveConfig.3 = "14.00"
# enterprises.ucdavis.loadTable.laEntry.loadaveErrorFlag.1 = 0
# enterprises.ucdavis.loadTable.laEntry.loadaveErrorFlag.2 = 0
# enterprises.ucdavis.loadTable.laEntry.loadaveErrorFlag.3 = 0
# enterprises.ucdavis.loadTable.laEntry.loadaveErrMessage.1 = ""
# enterprises.ucdavis.loadTable.laEntry.loadaveErrMessage.2 = ""
# enterprises.ucdavis.loadTable.laEntry.loadaveErrMessage.3 = ""

# -----------------------------------------------------------------------------


###############################################################################
# Extensible sections.
# 

# This alleviates the multiple line output problem found in the
# previous executable mib by placing each mib in its own mib table:

# Run a shell script containing:
#
# #!/bin/sh
# echo hello world
# echo hi there
# exit 35
#
# Note:  this has been specifically commented out to prevent
# accidental security holes due to someone else on your system writing
# a /tmp/shtest before you do.  Uncomment to use it.
#
# exec .1.3.6.1.4.1.2021.50 shelltest /bin/sh /tmp/shtest

# % snmpwalk -v 1 localhost public .1.3.6.1.4.1.2021.50
# enterprises.ucdavis.50.1.1 = 1
# enterprises.ucdavis.50.2.1 = "shelltest"
# enterprises.ucdavis.50.3.1 = "/bin/sh /tmp/shtest"
# enterprises.ucdavis.50.100.1 = 35
# enterprises.ucdavis.50.101.1 = "hello world."
# enterprises.ucdavis.50.101.2 = "hi there."
# enterprises.ucdavis.50.102.1 = 0

# Now the Output has grown to two lines, and we can see the 'hi
# there.' output as the second line from our shell script.
#
# Note that you must alter the mib.txt file to be correct if you want
# the .50.* outputs above to change to reasonable text descriptions.

# Other ideas:
# 
# exec .1.3.6.1.4.1.2021.51 ps /bin/ps 
# exec .1.3.6.1.4.1.2021.52 top /usr/bin/top
# exec .1.3.6.1.4.1.2021.53 mailq /usr/bin/mailq

# -----------------------------------------------------------------------------


###############################################################################
# Pass through control.
# 

# Usage:
#   pass MIBOID EXEC-COMMAND
#
# This will pass total control of the mib underneath the MIBOID
# portion of the mib to the EXEC-COMMAND.  
#
# Note:  You'll have to change the path of the passtest script to your
# source directory or install it in the given location.
# 
# Example:  (see the script for details)
#           (commented out here since it requires that you place the
#           script in the right location. (its not installed by default))

# pass .1.3.6.1.4.1.2021.255 /bin/sh /usr/local/passtest

# % snmpwalk -v 1 localhost public .1.3.6.1.4.1.2021.255
# enterprises.ucdavis.255.1 = "life the universe and everything"
# enterprises.ucdavis.255.2.1 = 42
# enterprises.ucdavis.255.2.2 = OID: 42.42.42
# enterprises.ucdavis.255.3 = Timeticks: (363136200) 42 days, 0:42:42
# enterprises.ucdavis.255.4 = IpAddress: 127.0.0.1
# enterprises.ucdavis.255.5 = 42
# enterprises.ucdavis.255.6 = Gauge: 42
#
# % snmpget -v 1 localhost public .1.3.6.1.4.1.2021.255.5
# enterprises.ucdavis.255.5 = 42
#
# % snmpset -v 1 localhost public .1.3.6.1.4.1.2021.255.1 s "New string"
# enterprises.ucdavis.255.1 = "New string"
#

# For specific usage information, see the man/snmpd.conf.5 manual page
# as well as the local/passtest script used in the above example.
Commit	Line	Data
f2121eaa AF	1	###############################################################################
	2	#
	3	# EXAMPLE.conf:
	4	# An example configuration file for configuring the net-snmp snmpd agent.
	5	#
	6	###############################################################################
	7	#
	8	# This file is intended to only be an example. If, however, you want
	9	# to use it, it should be placed in /etc/snmp/snmpd.conf.
	10	# When the snmpd agent starts up, this is where it will look for it.
	11	#
	12	# All lines beginning with a '#' are comments and are intended for you
	13	# to read. All other lines are configuration commands for the agent.
	14
	15	#
	16	# PLEASE: read the snmpd.conf(5) manual page as well!
	17
	18	#agentaddress 161,tcp:161
	19
	20	###############################################################################
	21	# System contact information
	22	#
	23
	24	# It is also possible to set the sysContact and sysLocation system
	25	# variables through the snmpd.conf file:
	26
	27	syslocation Unknown
	28	syscontact Root <root@localhost>
	29
	30	# Example output of snmpwalk:
	31	# % snmpwalk -v 1 localhost public system
	32	# system.sysDescr.0 = "PLD Linux"
	33	# system.sysObjectID.0 = OID: enterprises.ucdavis.ucdSnmpAgent.sunos4
	34	# system.sysUpTime.0 = Timeticks: (595637548) 68 days, 22:32:55
	35	# system.sysContact.0 = "Root <root@localhost>"
	36	# system.sysName.0 = "name"
	37	# system.sysLocation.0 = "Right here, right now."
	38	# system.sysServices.0 = 72
	39
	40	###############################################################################
	41	# Access Control
	42	###############################################################################
	43
	44	# By far, the most common question I get about the agent is "why won't
	45	# it work?", when really it should be "how do I configure the agent to
	46	# allow me to access it?"
	47	#
	48	# By default, the agent responds to the "public" community for read
	49	# only access, if run out of the box without any configuration file in
	50	# place. The following examples show you other ways of configuring
	51	# the agent so that you can change the community names, and give
	52	# yourself write access as well.
	53
	54	# The following lines change the access permissions of the agent so
	55	# that the COMMUNITY string provides read-only access to your entire
	56	# NETWORK (EG: 10.10.10.0/24), and read/write access to only the
	57	# localhost (127.0.0.1, not its real ipaddress).
	58
	59	# For more information, read the FAQ as well as the snmpd.conf(5)
	60	# manual page.
	61
	62	####
	63	# First, map the community name (COMMUNITY) into a security name
	64	# (local and mynetwork, depending on where the request is coming
65	# from):
66
67	# sec.name source community
68	com2sec local localhost public
69	com2sec theworld default public
70
71	####
72	# Second, map the security names into group names:
73
74	# sec.model sec.name
75	group MyRWGroup v2c local
76	group MyROGroup v2c theworld
77
78	####
79	# Third, create a view for us to let the groups have rights to:
80
81	# incl/excl subtree mask
82	view all included .1 80
83
84	####
85	# Finally, grant the 2 groups access to the 1 view with different
86	# write permissions:
87
88	# context sec.model sec.level prefix read write notif
89	access MyROGroup "" any noauth exact all none none
90	access MyRWGroup "" any noauth exact all all none
91
92	# -----------------------------------------------------------------------------
93
94
95
96
97	# -----------------------------------------------------------------------------
98
99
100	###############################################################################
101	# Process checks.
102	#
103	# The following are examples of how to use the agent to check for
104	# processes running on the host. The syntax looks something like:
105	#
106	# proc NAME [MAX=0] [MIN=0]
107	#
108	# NAME: the name of the process to check for. It must match
109	# exactly (ie, http will not find httpd processes).
110	# MAX: the maximum number allowed to be running. Defaults to 0.
111	# MIN: the minimum number to be running. Defaults to 0.
112
113	#
114	# Examples:
115	#
116
117	# Make sure mountd is running
118	# proc mountd
119
120	# Make sure there are no more than 4 ntalkds running, but 0 is ok too.
121	# proc ntalkd 4
122
123	# Make sure at least one sendmail, but less than or equal to 10 are running.
124	# proc sendmail 10 1
125
126	# A snmpwalk of the process mib tree would look something like this:
127	#
128	# % snmpwalk -v 1 localhost public .1.3.6.1.4.1.2021.2
129	# enterprises.ucdavis.procTable.prEntry.prIndex.1 = 1
130	# enterprises.ucdavis.procTable.prEntry.prIndex.2 = 2
131	# enterprises.ucdavis.procTable.prEntry.prIndex.3 = 3
132	# enterprises.ucdavis.procTable.prEntry.prNames.1 = "mountd"
133	# enterprises.ucdavis.procTable.prEntry.prNames.2 = "ntalkd"
134	# enterprises.ucdavis.procTable.prEntry.prNames.3 = "sendmail"
135	# enterprises.ucdavis.procTable.prEntry.prMin.1 = 0
136	# enterprises.ucdavis.procTable.prEntry.prMin.2 = 0
137	# enterprises.ucdavis.procTable.prEntry.prMin.3 = 1
138	# enterprises.ucdavis.procTable.prEntry.prMax.1 = 0
139	# enterprises.ucdavis.procTable.prEntry.prMax.2 = 4
140	# enterprises.ucdavis.procTable.prEntry.prMax.3 = 10
141	# enterprises.ucdavis.procTable.prEntry.prCount.1 = 0
142	# enterprises.ucdavis.procTable.prEntry.prCount.2 = 0
143	# enterprises.ucdavis.procTable.prEntry.prCount.3 = 1
144	# enterprises.ucdavis.procTable.prEntry.prErrorFlag.1 = 1
145	# enterprises.ucdavis.procTable.prEntry.prErrorFlag.2 = 0
146	# enterprises.ucdavis.procTable.prEntry.prErrorFlag.3 = 0
147	# enterprises.ucdavis.procTable.prEntry.prErrMessage.1 = "No mountd process running."
148	# enterprises.ucdavis.procTable.prEntry.prErrMessage.2 = ""
149	# enterprises.ucdavis.procTable.prEntry.prErrMessage.3 = ""
150	# enterprises.ucdavis.procTable.prEntry.prErrFix.1 = 0
151	# enterprises.ucdavis.procTable.prEntry.prErrFix.2 = 0
152	# enterprises.ucdavis.procTable.prEntry.prErrFix.3 = 0
153	#
154	# Note that the errorFlag for mountd is set to 1 because one is not
155	# running (in this case an rpc.mountd is, but thats not good enough),
156	# and the ErrMessage tells you what's wrong. The configuration
157	# imposed in the snmpd.conf file is also shown.
158	#
159	# Special Case: When the min and max numbers are both 0, it assumes
160	# you want a max of infinity and a min of 1.
161	#
162
163
164	# -----------------------------------------------------------------------------
165
166
167	###############################################################################
168	# Executables/scripts
169	#
170
171	#
172	# You can also have programs run by the agent that return a single
173	# line of output and an exit code. Here are two examples.
174	#
175	# exec NAME PROGRAM [ARGS ...]
176	#
177	# NAME: A generic name.
178	# PROGRAM: The program to run. Include the path!
179	# ARGS: optional arguments to be passed to the program
180
181	# a simple hello world
30fd5608	182	#exec echotest /bin/echo hello world
f2121eaa AF	183
	184	# Run a shell script containing:
	185	#
	186	# #!/bin/sh
	187	# echo hello world
	188	# echo hi there
	189	# exit 35
	190	#
	191	# Note: this has been specifically commented out to prevent
	192	# accidental security holes due to someone else on your system writing
	193	# a /tmp/shtest before you do. Uncomment to use it.
	194	#
	195	#exec shelltest /bin/sh /tmp/shtest
	196
	197	# Then,
	198	# % snmpwalk -v 1 localhost public .1.3.6.1.4.1.2021.8
	199	# enterprises.ucdavis.extTable.extEntry.extIndex.1 = 1
	200	# enterprises.ucdavis.extTable.extEntry.extIndex.2 = 2
	201	# enterprises.ucdavis.extTable.extEntry.extNames.1 = "echotest"
	202	# enterprises.ucdavis.extTable.extEntry.extNames.2 = "shelltest"
	203	# enterprises.ucdavis.extTable.extEntry.extCommand.1 = "/bin/echo hello world"
	204	# enterprises.ucdavis.extTable.extEntry.extCommand.2 = "/bin/sh /tmp/shtest"
	205	# enterprises.ucdavis.extTable.extEntry.extResult.1 = 0
	206	# enterprises.ucdavis.extTable.extEntry.extResult.2 = 35
	207	# enterprises.ucdavis.extTable.extEntry.extOutput.1 = "hello world."
	208	# enterprises.ucdavis.extTable.extEntry.extOutput.2 = "hello world."
	209	# enterprises.ucdavis.extTable.extEntry.extErrFix.1 = 0
	210	# enterprises.ucdavis.extTable.extEntry.extErrFix.2 = 0
	211
	212	# Note that the second line of the /tmp/shtest shell script is cut
	213	# off. Also note that the exit status of 35 was returned.
	214
	215	# -----------------------------------------------------------------------------
	216
	217
	218	###############################################################################
	219	# disk checks
	220	#
	221
	222	# The agent can check the amount of available disk space, and make
	223	# sure it is above a set limit.
	224
	225	# disk PATH [MIN=100000]
	226	#
	227	# PATH: mount path to the disk in question.
	228	# MIN: Disks with space below this value will have the Mib's errorFlag set.
	229	# Default value = 100000.
	230
	231	# Check the / partition and make sure it contains at least 10 megs.
	232
	233	disk / 10000
	234
	235	# % snmpwalk -v 1 localhost public .1.3.6.1.4.1.2021.9
	236	# enterprises.ucdavis.diskTable.dskEntry.diskIndex.1 = 0
	237	# enterprises.ucdavis.diskTable.dskEntry.diskPath.1 = "/" Hex: 2F
	238	# enterprises.ucdavis.diskTable.dskEntry.diskDevice.1 = "/dev/dsk/c201d6s0"
	239	# enterprises.ucdavis.diskTable.dskEntry.diskMinimum.1 = 10000
	240	# enterprises.ucdavis.diskTable.dskEntry.diskTotal.1 = 837130
	241	# enterprises.ucdavis.diskTable.dskEntry.diskAvail.1 = 316325
	242	# enterprises.ucdavis.diskTable.dskEntry.diskUsed.1 = 437092
	243	# enterprises.ucdavis.diskTable.dskEntry.diskPercent.1 = 58
	244	# enterprises.ucdavis.diskTable.dskEntry.diskErrorFlag.1 = 0
	245	# enterprises.ucdavis.diskTable.dskEntry.diskErrorMsg.1 = ""
	246
247	# -----------------------------------------------------------------------------
248
249
250	###############################################################################
251	# load average checks
252	#
253
254	# load [1MAX=12.0] [5MAX=12.0] [15MAX=12.0]
255	#
256	# 1MAX: If the 1 minute load average is above this limit at query
257	# time, the errorFlag will be set.
258	# 5MAX: Similar, but for 5 min average.
259	# 15MAX: Similar, but for 15 min average.
260
261	# Check for loads:
262	load 12 14 14
263
264	# % snmpwalk -v 1 localhost public .1.3.6.1.4.1.2021.10
265	# enterprises.ucdavis.loadTable.laEntry.loadaveIndex.1 = 1
266	# enterprises.ucdavis.loadTable.laEntry.loadaveIndex.2 = 2
267	# enterprises.ucdavis.loadTable.laEntry.loadaveIndex.3 = 3
268	# enterprises.ucdavis.loadTable.laEntry.loadaveNames.1 = "Load-1"
269	# enterprises.ucdavis.loadTable.laEntry.loadaveNames.2 = "Load-5"
270	# enterprises.ucdavis.loadTable.laEntry.loadaveNames.3 = "Load-15"
271	# enterprises.ucdavis.loadTable.laEntry.loadaveLoad.1 = "0.49" Hex: 30 2E 34 39
272	# enterprises.ucdavis.loadTable.laEntry.loadaveLoad.2 = "0.31" Hex: 30 2E 33 31
273	# enterprises.ucdavis.loadTable.laEntry.loadaveLoad.3 = "0.26" Hex: 30 2E 32 36
274	# enterprises.ucdavis.loadTable.laEntry.loadaveConfig.1 = "12.00"
275	# enterprises.ucdavis.loadTable.laEntry.loadaveConfig.2 = "14.00"
276	# enterprises.ucdavis.loadTable.laEntry.loadaveConfig.3 = "14.00"
277	# enterprises.ucdavis.loadTable.laEntry.loadaveErrorFlag.1 = 0
278	# enterprises.ucdavis.loadTable.laEntry.loadaveErrorFlag.2 = 0
279	# enterprises.ucdavis.loadTable.laEntry.loadaveErrorFlag.3 = 0
280	# enterprises.ucdavis.loadTable.laEntry.loadaveErrMessage.1 = ""
281	# enterprises.ucdavis.loadTable.laEntry.loadaveErrMessage.2 = ""
282	# enterprises.ucdavis.loadTable.laEntry.loadaveErrMessage.3 = ""
283
284	# -----------------------------------------------------------------------------
285
286
287	###############################################################################
288	# Extensible sections.
289	#
290
291	# This alleviates the multiple line output problem found in the
292	# previous executable mib by placing each mib in its own mib table:
293
294	# Run a shell script containing:
295	#
296	# #!/bin/sh
297	# echo hello world
298	# echo hi there
299	# exit 35
300	#
301	# Note: this has been specifically commented out to prevent
302	# accidental security holes due to someone else on your system writing
303	# a /tmp/shtest before you do. Uncomment to use it.
304	#
305	# exec .1.3.6.1.4.1.2021.50 shelltest /bin/sh /tmp/shtest
306
307	# % snmpwalk -v 1 localhost public .1.3.6.1.4.1.2021.50
308	# enterprises.ucdavis.50.1.1 = 1
309	# enterprises.ucdavis.50.2.1 = "shelltest"
310	# enterprises.ucdavis.50.3.1 = "/bin/sh /tmp/shtest"
311	# enterprises.ucdavis.50.100.1 = 35
312	# enterprises.ucdavis.50.101.1 = "hello world."
313	# enterprises.ucdavis.50.101.2 = "hi there."
314	# enterprises.ucdavis.50.102.1 = 0
315
316	# Now the Output has grown to two lines, and we can see the 'hi
317	# there.' output as the second line from our shell script.
318	#
319	# Note that you must alter the mib.txt file to be correct if you want
320	# the .50.* outputs above to change to reasonable text descriptions.
321
322	# Other ideas:
323	#
324	# exec .1.3.6.1.4.1.2021.51 ps /bin/ps
325	# exec .1.3.6.1.4.1.2021.52 top /usr/bin/top
326	# exec .1.3.6.1.4.1.2021.53 mailq /usr/bin/mailq
327
328	# -----------------------------------------------------------------------------
329
330
331	###############################################################################
332	# Pass through control.
333	#
334
335	# Usage:
336	# pass MIBOID EXEC-COMMAND
337	#
338	# This will pass total control of the mib underneath the MIBOID
339	# portion of the mib to the EXEC-COMMAND.
340	#
341	# Note: You'll have to change the path of the passtest script to your
342	# source directory or install it in the given location.
343	#
344	# Example: (see the script for details)
345	# (commented out here since it requires that you place the
346	# script in the right location. (its not installed by default))
347
348	# pass .1.3.6.1.4.1.2021.255 /bin/sh /usr/local/passtest
349
350	# % snmpwalk -v 1 localhost public .1.3.6.1.4.1.2021.255
351	# enterprises.ucdavis.255.1 = "life the universe and everything"
352	# enterprises.ucdavis.255.2.1 = 42
353	# enterprises.ucdavis.255.2.2 = OID: 42.42.42
354	# enterprises.ucdavis.255.3 = Timeticks: (363136200) 42 days, 0:42:42
355	# enterprises.ucdavis.255.4 = IpAddress: 127.0.0.1
356	# enterprises.ucdavis.255.5 = 42
357	# enterprises.ucdavis.255.6 = Gauge: 42
358	#
359	# % snmpget -v 1 localhost public .1.3.6.1.4.1.2021.255.5
360	# enterprises.ucdavis.255.5 = 42
361	#
362	# % snmpset -v 1 localhost public .1.3.6.1.4.1.2021.255.1 s "New string"
363	# enterprises.ucdavis.255.1 = "New string"
364	#
365
366	# For specific usage information, see the man/snmpd.conf.5 manual page
367	# as well as the local/passtest script used in the above example.