- added description of djurban's branch

[packages/kernel.git] / linux-2.4.25-vlan-3c59x.patch

--- linux.orig/drivers/net/3c59x.c	Sun Sep 30 21:26:06 2001
+++ linux/drivers/net/3c59x.c	Wed Oct 24 21:52:10 2001
@@ -308,6 +308,9 @@
    code size of a per-interface flag is not worthwhile. */
 static char mii_preamble_required;
 
+/* The Ethernet Type used for 802.1q tagged frames */
+#define VLAN_ETHER_TYPE 0x8100
+
 #define PFX DRV_NAME ": "
 
 
@@ -651,7 +654,7 @@
 	Wn2_ResetOptions=12,
 };
 enum Window3 {			/* Window 3: MAC/config bits. */
-	Wn3_Config=0, Wn3_MAC_Ctrl=6, Wn3_Options=8,
+	Wn3_Config=0, Wn3_MaxPktSize=4, Wn3_MAC_Ctrl=6, Wn3_Options=8,
 };
 
 #define BFEXT(value, offset, bitcount)  \
@@ -679,7 +682,8 @@
 	Media_LnkBeat = 0x0800,
 };
 enum Window7 {					/* Window 7: Bus Master control. */
-	Wn7_MasterAddr = 0, Wn7_MasterLen = 6, Wn7_MasterStatus = 12,
+	Wn7_MasterAddr = 0, Wn7_VlanEtherType=4, Wn7_MasterLen = 6,
+	Wn7_MasterStatus = 12,
 };
 /* Boomerang bus master control registers. */
 enum MasterCtrl {
@@ -776,7 +780,8 @@
 		pm_state_valid:1,				/* power_state[] has sane contents */
 		open:1,
 		medialock:1,
-		must_free_region:1;				/* Flag: if zero, Cardbus owns the I/O region */
+		must_free_region:1,				/* Flag: if zero, Cardbus owns the I/O region */
+		large_frames:1;			/* accept large frames */
 	int drv_flags;
 	u16 status_enable;
 	u16 intr_enable;
@@ -844,6 +849,9 @@
 static void vortex_tx_timeout(struct net_device *dev);
 static void acpi_set_WOL(struct net_device *dev);
 static struct ethtool_ops vortex_ethtool_ops;
+#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
+static void set_8021q_mode(struct net_device *dev, int enable);
+#endif
 \f
 /* This driver uses 'options' to pass the media type, full-duplex flag, etc. */
 /* Option count limit only -- unlimited interfaces are supported. */
@@ -1030,6 +1038,7 @@
 	dev->base_addr = ioaddr;
 	dev->irq = irq;
 	dev->mtu = mtu;
+	vp->large_frames = mtu > 1500;
 	vp->drv_flags = vci->drv_flags;
 	vp->has_nway = (vci->drv_flags & HAS_NWAY) ? 1 : 0;
 	vp->io_size = vci->io_size;
@@ -1461,7 +1470,7 @@
 
 	/* Set the full-duplex bit. */
 	outw(	((vp->info1 & 0x8000) || vp->full_duplex ? 0x20 : 0) |
-		 	(dev->mtu > 1500 ? 0x40 : 0) |
+		 	(vp->large_frames ? 0x40 : 0) |
 			((vp->full_duplex && vp->flow_ctrl && vp->partner_flow_ctrl) ? 0x100 : 0),
 			ioaddr + Wn3_MAC_Ctrl);
 
@@ -1545,6 +1554,10 @@
 	}
 	/* Set receiver mode: presumably accept b-case and phys addr only. */
 	set_rx_mode(dev);
+#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
+	/* enable 802.1q tagged frames */
+	set_8021q_mode(dev, 1);
+#endif
 	outw(StatsEnable, ioaddr + EL3_CMD); /* Turn on statistics. */
 
 //	issue_and_wait(dev, SetTxStart|0x07ff);
@@ -1680,7 +1693,7 @@
 						/* Set the full-duplex bit. */
 						EL3WINDOW(3);
 						outw(	(vp->full_duplex ? 0x20 : 0) |
-								(dev->mtu > 1500 ? 0x40 : 0) |
+								(vp->large_frames ? 0x40 : 0) |
 								((vp->full_duplex && vp->flow_ctrl && vp->partner_flow_ctrl) ? 0x100 : 0),
 								ioaddr + Wn3_MAC_Ctrl);
 						if (vortex_debug > 1)
@@ -1900,6 +1913,10 @@
 			issue_and_wait(dev, RxReset|0x07);
 			/* Set the Rx filter to the current state. */
 			set_rx_mode(dev);
+#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
+			/* enable 802.1q VLAN tagged frames */
+			set_8021q_mode(dev, 1);
+#endif
 			outw(RxEnable, ioaddr + EL3_CMD); /* Re-enable the receiver. */
 			outw(AckIntr | HostError, ioaddr + EL3_CMD);
 		}
@@ -2497,6 +2514,11 @@
 	outw(RxDisable, ioaddr + EL3_CMD);
 	outw(TxDisable, ioaddr + EL3_CMD);
 
+#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
+	/* Disable receiving 802.1q tagged frames */
+	set_8021q_mode(dev, 0);
+#endif
+
 	if (dev->if_port == XCVR_10base2)
 		/* Turn off thinnet power.  Green! */
 		outw(StopCoax, ioaddr + EL3_CMD);
@@ -2760,6 +2782,50 @@
 
 	outw(new_mode, ioaddr + EL3_CMD);
 }
+
+#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
+/* Setup the card so that it can receive frames with an 802.1q VLAN tag.
+   Note that this must be done after each RxReset due to some backwards
+   compatibility logic in the Cyclone and Tornado ASICs */
+static void set_8021q_mode(struct net_device *dev, int enable)
+{
+	struct vortex_private *vp = (struct vortex_private *)dev->priv;
+	long ioaddr = dev->base_addr;
+	int old_window = inw(ioaddr + EL3_CMD);
+	int mac_ctrl;
+	
+	if (vp->drv_flags&IS_CYCLONE || vp->drv_flags&IS_TORNADO) {
+		/* cyclone and tornado chipsets can recognize 802.1q
+		 * tagged frames and treat them correctly */
+
+		int max_pkt_size = dev->mtu+14;	/* MTU+Ethernet header */
+		if (enable)
+			max_pkt_size += 4;	/* 802.1Q VLAN tag */
+
+		EL3WINDOW(3);
+		outw(max_pkt_size, ioaddr+Wn3_MaxPktSize);
+
+		/* set VlanEtherType to let the hardware checksumming
+		   treat tagged frames correctly */
+		EL3WINDOW(7);
+		outw(VLAN_ETHER_TYPE, ioaddr+Wn7_VlanEtherType);
+	} else {
+		/* on older cards we have to enable large frames */
+
+		vp->large_frames = dev->mtu > 1500 || enable;
+
+		EL3WINDOW(3);
+		mac_ctrl = inw(ioaddr+Wn3_MAC_Ctrl);
+		if (vp->large_frames)
+			mac_ctrl |= 0x40;
+		else
+			mac_ctrl &= ~0x40;
+		outw(mac_ctrl, ioaddr+Wn3_MAC_Ctrl);
+	}
+
+	EL3WINDOW(old_window);
+}
+#endif
 
 /* MII transceiver control section.
    Read and write the MII registers using software-generated serial