--- /dev/null
+--- diag-ether/eepro100-diag.c.org 2004-02-22 21:31:11.000000000 +0000
++++ diag-ether/eepro100-diag.c 2004-02-22 21:33:36.000000000 +0000
+@@ -34,37 +34,36 @@
+ " For details and other options see http://www.scyld.com/diag/index.html\n";
+
+ static const char long_usage_msg[] =
+-"Usage: %s [-aDfrRvVw] [-AF <speed+duplex>] [-#<BoardNum>]
+-
+- Show the internal state of a network adapter.
+-
+- The common usage is
+- diag -aem
+-
+- Frequently used options are
+- -a --show_all_registers Print all registers.
+- -e --show-eeprom Dump EEPROM contents, \"-ee\" shows the details.
+- -m --show_mii Print the MII transceiver state
+- Using -mm monitors the link.
+- -f --force Perform operation, even on a running NIC.
+-
+- To operate on a single NIC, or one that hasn't been automatically found:
+- -# --card_num INDEX Operate on the specified card index.
+- -p --port-base IOADDR Assume an adapter at the specified I/O address.
+- -t --chip-type TYPE Specify adapter type (with '-p'), use '-1' to list.
+-
+- To change the persistent EEPROM settings
+- -G --parameters PARMS Set adapter-specific parameters.
+- -H --new-hwaddr 01:23:45:67:89:ab
+- Set a new hardware station address. Typically disabled for safety.
+- -w --write-EEPROM Actually write the new settings into the EEPROM.
+-
+- -D --debug
+- -v --verbose Report each action taken.
+- -V --version Emit version information.
+-
+- -A --advertise <speed|setting> (See the mii-diag manual page.)
+-";
++"Usage: %s [-aDfrRvVw] [-AF <speed+duplex>] [-#<BoardNum>]\n"
++"\n"
++" Show the internal state of a network adapter.\n"
++"\n"
++" The common usage is\n"
++" diag -aem\n"
++"\n"
++" Frequently used options are\n"
++" -a --show_all_registers Print all registers.\n"
++" -e --show-eeprom Dump EEPROM contents, \"-ee\" shows the details.\n"
++" -m --show_mii Print the MII transceiver state\n"
++" Using -mm monitors the link.\n"
++" -f --force Perform operation, even on a running NIC.\n"
++"\n"
++" To operate on a single NIC, or one that hasn't been automatically found:\n"
++" -# --card_num INDEX Operate on the specified card index.\n"
++" -p --port-base IOADDR Assume an adapter at the specified I/O address.\n"
++" -t --chip-type TYPE Specify adapter type (with '-p'), use '-1' to list.\n"
++"\n"
++" To change the persistent EEPROM settings\n"
++" -G --parameters PARMS Set adapter-specific parameters.\n"
++" -H --new-hwaddr 01:23:45:67:89:ab\n"
++" Set a new hardware station address. Typically disabled for safety.\n"
++" -w --write-EEPROM Actually write the new settings into the EEPROM.\n"
++"\n"
++" -D --debug\n"
++" -v --verbose Report each action taken.\n"
++" -V --version Emit version information.\n"
++"\n"
++" -A --advertise <speed|setting> (See the mii-diag manual page.)\n\n";
+
+ #if ! defined(__OPTIMIZE__)
+ #warning You must compile this program with the correct options!