--- linux-2.6.15.6/drivers/input/joystick/iforce/iforce-serio.c 2006-03-05 19:07:54.000000000 +0000 +++ linux-2.6.15.6.iforce/drivers/input/joystick/iforce/iforce-serio.c 2006-04-29 23:17:59.000000000 +0000 @@ -175,6 +175,12 @@ .id = SERIO_ANY, .extra = SERIO_ANY, }, + { + .type = SERIO_RS232, + .proto = 0x1f, // Trust ForceFeedback Race Master + .id = SERIO_ANY, + .extra = SERIO_ANY, + }, { 0 } }; --- linux-2.6.27/arch/powerpc/include/asm/io.h~ 2006-06-18 01:49:35.000000000 +0000 +++ linux-2.6.27/arch/powerpc/include/asm/io.h 2006-06-22 02:44:19.000000000 +0000 @@ -445,6 +445,10 @@ #define page_to_phys(page) (page_to_pfn(page) << PAGE_SHIFT) #define page_to_bus(page) (page_to_phys(page) + PCI_DRAM_OFFSET) +#define isa_virt_to_bus virt_to_phys +#define isa_page_to_bus page_to_phys +#define isa_bus_to_virt phys_to_virt + /* Enforce in-order execution of data I/O. * No distinction between read/write on PPC; use eieio for all three. */ --- linux-2.6.27/arch/powerpc/include/asm/suspend.h 2007-07-09 01:32:17.000000000 +0200 +++ linux-2.6.27/arch/powerpc/include/asm/suspend.h 2007-08-28 23:26:16.629658848 +0200 @@ -6,4 +6,7 @@ void save_processor_state(void); void restore_processor_state(void); +#define suspend2_faulted (0) +#define clear_suspend2_fault() do { } while(0) + #endif /* __ASM_POWERPC_SUSPEND_H */ --- linux-2.6.26/arch/powerpc/kernel/swsusp.c 2008-09-29 00:01:56.000000000 +0200 +++ linux-2.6.26/arch/powerpc/kernel/swsusp.c 2008-09-29 00:01:42.000000000 +0200 @@ -9,6 +9,7 @@ * 2 of the License, or (at your option) any later version. */ +#include #include #include #include @@ -30,6 +31,7 @@ #endif } +EXPORT_SYMBOL(save_processor_state); void restore_processor_state(void) { --- linux-2.6.32/drivers/infiniband/Kconfig~ 2009-12-05 00:26:03.663774916 +0100 +++ linux-2.6.32/drivers/infiniband/Kconfig 2009-12-05 00:26:05.914179759 +0100 @@ -37,7 +37,6 @@ config INFINIBAND_ADDR_TRANS bool depends on INET - depends on !(INFINIBAND = y && IPV6 = m) default y source "drivers/infiniband/hw/mthca/Kconfig" --- linux-2.6.33/scripts/mod/modpost.c~ 2010-02-24 19:52:17.000000000 +0100 +++ linux-2.6.33/scripts/mod/modpost.c 2010-03-07 14:26:47.242168558 +0100 @@ -15,7 +15,8 @@ #include #include #include "modpost.h" -#include "../../include/generated/autoconf.h" +// PLD architectures don't use CONFIG_SYMBOL_PREFIX +//#include "../../include/generated/autoconf.h" #include "../../include/linux/license.h" /* Some toolchains use a `_' prefix for all user symbols. */ commit 87b09f1f25cd1e01d7c50bf423c7fe33027d7511 Author: stephen hemminger Date: Fri Feb 12 06:58:00 2010 +0000 sky2: dont enable PME legacy mode This bit is not changed by vendor driver, and should be left alone. The documentation implies this a debug bit. 0 = WAKE# only asserted when VMAIN not available 1 = WAKE# is depend on wake events and independent of VMAIN. Signed-off-by: Stephen Hemminger Signed-off-by: David S. Miller diff --git b/drivers/net/sky2.c a/drivers/net/sky2.c index 2494842..edf37aa 100644 --- b/drivers/net/sky2.c +++ a/drivers/net/sky2.c @@ -733,6 +733,7 @@ static void sky2_wol_init(struct sky2_port *sky2) unsigned port = sky2->port; enum flow_control save_mode; u16 ctrl; + u32 reg1; /* Bring hardware out of reset */ sky2_write16(hw, B0_CTST, CS_RST_CLR); @@ -786,6 +787,11 @@ static void sky2_wol_init(struct sky2_port *sky2) /* Disable PiG firmware */ sky2_write16(hw, B0_CTST, Y2_HW_WOL_OFF); + /* Turn on legacy PCI-Express PME mode */ + reg1 = sky2_pci_read32(hw, PCI_DEV_REG1); + reg1 |= PCI_Y2_PME_LEGACY; + sky2_pci_write32(hw, PCI_DEV_REG1, reg1); + /* block receiver */ sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET); }